Posts in category "project" - page 7
-
Experience With Flutter
In one of my previous posts I mentioned about a project that I wrote entirely using Flutter. This is the continuation of that post. I will go into the details of how Flutter became the platform of choice and my experience with it. Let me preface by saying that this may be interesting only to a limited set of software engineers. So if you are not one of them, it'll serve you best to skip this post.
...continue reading -
The Friends Roster Project
While 2020 has tied many people to their homes, it also encouraged many to seek out old friends. The same happened with me and a bunch of my friends. I have lost touch with a lot of my school, college and work friends as the years passed. You find new friends. You get busy with work and family and eventually don't find time to call or meet friends as much as you might have when you were young.
...continue reading -
Building a DIY 5.1 Audio Video Receiver – Part 7
Now that I have the front speakers, rear speakers and sub-woofer working, the next thing I wanted to do in my DIY AVR project was to bring up the center speaker. I ordered a TPA3118 amplifier board for Rs. 379 towards it. The only problem with the board (which I did not realize when I ordered it) was that it does not have a volume control. The repercussions of this mistake will soon become clear. Anyway, I connected the board to a 12V power supply. The same one that was powering the crossover board from my previous post. Output from the board is connected to my center speaker. The sound quality is fine to my ears. Anyway it is the center speaker, so we don't need a great quality output.
...continue reading -
Building a DIY 5.1 Audio Video Receiver – Part 6
In the last post I mentioned that I was looking for a crossover board. The one that I purchased is putting out a huge DC bias and I was not comfortable using it on my sub woofer. Wondering if it is a problem with the particular unit that I got, I ordered a replacement. Unfortunately, even the replacement has the same signature output. So I decided to do something about it myself.
...continue reading -
Building a DIY 5.1 Audio Video Receiver – Part 5
So far I have finished bringing up 4 of my 5.1 speakers in my DIY 5.1 AVR project. If you missed, check out part 1, part 2, part 3 and part 4 of the series. Next I wanted to bring up my sub-woofer. Since I have an active sub-woofer, I did not need any amplifiers to drive it. I just need to connect the output signal from my audio source directly to the sub-woofer input. But there is a catch. If you connect the audio source directly to the sub-woofer, the sub would be wasting a lot of energy which may heat up the driver and may damage it. Moreover driving the sub with all the frequencies will give boomy muddled up sound. So we need a low pass filter or a crossover.
...continue reading -
Building a DIY 5.1 Audio Video Receiver – Part 4
As I mentioned in my last post, after measuring the frequency response and testing the TDA 7498, I decided to buy one more. The board I bought earlier did not have the right LC filter for a 6 ohms speaker. It was designed for 8 ohms speaker. So I decided to use that board for my rear surround speakers which were also 6 ohms. However, it is fine to have a slightly poor quality amp for the rarely used rear speakers.
...continue reading -
Building a DIY 5.1 Audio Video Receiver – Part 3
The TDA7498 class D amplifier board that I purchased to power my front speakers was working great. The audio quality is at par with what my Pioneer 5.1 AVR delivered using class AB amplifier. I could not tell the difference in audio quality. None the less, I wanted to make sure the quality is really as good as my ears led me to believe. Enter a function generator and oscilloscope to make sure the frequency response is satisfactory over the range of audible frequencies (20 Hz to 20 kHz).
...continue reading -
Building a DIY 5.1 Audio Video Receiver – Part 2
If you did not read part 1 of building a DIY 5.1 AVR, I suggest you start from there. Here is some important points from my previous post --
...continue reading -
Building a DIY 5.1 Audio Video Receiver - Part 1
Alright, you already know the story of my electronics going puff during a power surge. One of the electronics that got burnt was my unnecessarily expensive Pioneer 5.1.2 AVR. The reason I put emphasis on unnecessary is because I rarely used all the features of the device. Don't even know why I spent all the money :). After it stopped working, I opened and checked everything that I could figure out. But I didn't notice any obvious problems. The AVR just boots up, turns on the amplifier relay and turns off. Since it failed during COVID lock down, I couldn't do much about it.
...continue reading -
Tax Filler Script
The Indian tax filing has become even more tedious now. Going forward, starting from assessment year 2020-21 (financial year 2019-2020) one needs to report each and every equity redemption that results in long term capital gain in Schedule 112A. It used to be optional last year. Instead of reporting every transaction you could just report the aggregate value. But it is not optional anymore. This increases the burden on the tax payer especially if you have made a lot of small transactions.
...continue reading